ASTM A682 PDF

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Tojakinos Kazira
Country: Portugal
Language: English (Spanish)
Genre: Literature
Published (Last): 19 September 2004
Pages: 263
PDF File Size: 20.1 Mb
ePub File Size: 1.17 Mb
ISBN: 658-4-51163-187-9
Downloads: 75819
Price: Free* [*Free Regsitration Required]
Uploader: Karr

A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense.

Strip tolerance products may be available in widths wider than ? Within the text, the SI units are shown in brackets.

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems will result in nonconformance with the speci?

However, unless the order speci? The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. NOTE 1—The term weight is used when inch-pound units are the standard. However, under SI the preferred term in mass.

Current edition approved March 10, Originally published as A — Last previous edition A — General Requirements for Delivery 4. Materials and Manufacture 5.

It is normally produced as a fully killed steel. Elements such as aluminum may be added in sufficient amounts to control the austenitic grain size. The elements comprising the desired chemical composition are speci? When the maximum manganese limit exceeds 1. Table 3 shows requirements for additional elements. Limits on such elements are by agreement between purchaser and supplier. Each of the elements listed in Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis.

When the amount of copper, nickel, chromium, or molybdenum is less than 0. When the amount of vanadium, columbium, or titanium is less than 0. The strip may be subjected to product analysis by the purchaser either for the purpose of verifying that the chemical composition is within speci? The results of analyses taken from different pieces within a heat may differ from each other and from the cast analysis.

  BALANCE POLAR ELECTROMAGNETICO PDF

When agreed by purchaser and supplier, other silicon ranges are permissible. Dimensions, Mass, and Permissible Variations 9.

ASTM A682 Grade 1074

Finish and Edges This is produced when the edge condition is not a critical requirement for the? Normal coiling or piling does not provide a 3 Where an ellipsis. B The sum of copper, nickel, chromium, and molybdenum shall not exceed 0. When one or more of these elements is speci? C When the chromium is speci? Thickness Tolerances Plus or Minus, in. B Measured 10 mm or more in from edge; and on narrower than 25 mm, at any place between edges.

C Number 3 edge strip with thickness tolerance guaranteed at less than 3? This edge is produced aa682 the width tolerance and edge condition are not as exacting as for No.

ASTM A, AM_百度文库

Number of Tests and Retests C When edge, width and thickness are not de? Two additional samples are secured from each end of the coil from which the original sample was taken.

A portion of the coil may be discarded prior to cutting the samples for retest. If any of the retests fail to comply with the requirements, the coil shall be rejected. Rework and Retreatment Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of production.

Over 12 Width Tolerance, Plus and Minus, in. Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the report. NOTE 2—The industry de?

Government procurement adtm the Defense Supply Agency, strip material shall be continuously marked for identi? The ability of manufacturers to meet the maximum coil weights depends upon individual mill equipment. When required, minimum coil weights are subject to negotiation. Rejection and Rehearing The material must be adequately protected and correctly identi? In case of dissatisfaction with the results of the test, the manufacturer may make claims for a rehearing.

  ANISOMELES MALABARICA PDF

However, the document shall clearly identify the organization submitting the document. Notwithstanding the absence of a signature, the organization submitting the document is responsible for the content of the document.

NOTE 2—Camber tolerances as shown in the table are for any 8 ft.

For strip length under 8 ft. NOTE 3—When the camber tolerances shown in Table 8 are not suitable for a particular purpose, cold-rolled strip is sometimes machine straightened.

Over 12 Through 11? NOTE 1—Camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge. NOTE a628 tolerances as shown in the table are for any mm length. For strip length under mm, camber tolerance shall be subject to negotiation.

Revision to Table 2. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be a862 every?

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown a62. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.