Please refer to the notes in the operating instructions. ProSafe™ Port L2 Managed Switch with Static Routing GSM has been. View and Download Netgear ProSafe GSM user manual online. Netgear ProSafe GSM User Manual. ProSafe GSM Switch pdf manual. Netgear ProSafe GSM Manual Online: Chapter 1: Introduction, Overview. Congratulations On Your Purchase Of A NETGEAR ProSafe GSM Managed .
|Published (Last):||11 January 2007|
|PDF File Size:||2.38 Mb|
|ePub File Size:||9.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
NETGEAR does not assume any liability that may occur due to the use or application of sgm7248 product s or circuit layout s described herein.
Switch Management Overview Scope Quick Start up User Account Management A-1 Category 5 Cable B xxiv ContentsMay Series L2 Switch software.
It is intended to provide an understanding of the configuration options of Series L2 Switch software. It is assumed that the reader has an understanding of the relevant switch platforms. It is also assumed that the reader has a basic knowledge of Ethernet and networking concepts.
Devices that are capable of switching Layers 2, 3, and 4 are increasingly in demand. Management is standards-based, with configuration parameters and a private MIB providing control for functions not completely specified in the MIBs.
Netgear ProSafe GSM7248 Operating Instructions Manual: Chapter 1: Introduction; Overview
Connection Settings Click OK. Login splash screen for the Managed Switch Click the Login link. A user name and password dialog box opens like this one. System Information page This welcome page displays system information, such as: Interactive switch image This dynamic image shows various real manal conditions about the switch, including the status, fan operation, power, and the connectivity and traffic indication for each port.
In addition, using the popup menus described below, you can directly access a wealth of information manal right-clicking on a port and selecting a menu item from the popup-menu that displays.
NETGEAR ProSafe GSM user manual – – Solve your problem
The online help contains a detailed description of the features on each screen. Switch popup menus You can access a port-specific popup menu by right clicking on the port in the image of the switch and browsing to the menu you want to use.
Each CLI command is illustrated using the structure outlined below. The text in bold italics should be replaced with a name or number. To use spaces as part of a name parameter, enclose it in double quotes like this: Network addresses are shown using the following syntax: In-band connectivity allows access to the Series L2 Switch locally or from a remote workstation.
The user should do a copy system: Quick Start up IP Address A sample of the CLI command modes are described below. Each of the command modes support specific Series L2 Switch commands. Global Config Mode From the Privileged Some of the modes are depicted in the mode-based CLI Figure 1. The Commands in one mode are not available until the operator switches to that particular mode, with the exception of the User Exec mode commands.
Only the configuration commands are available in the “no”form. The commands are divided into five functional groups: Note that this does not include multicast packets. The trap log contains a maximum of entries that wrap.
GSMv2 | Product | Support | NETGEAR
If the command is entered with no parameter, the entire table is displayed. This is the same as entering the optional Alternatively, the administrator can enter a MAC Address to display the table entry for the requested MAC address and all entries following the requested MAC address.
The message log contains system trace information. The range for name, location and contact is from 1 to 31 alphanumeric If sessions are enabled, new telnet sessions can be established until there are no more sessions available. If sessions are disabled, no new telnet sessions are established.
A value of 0 indicates that no outbound telnet session can be established. In an IVL system, the [fdbid all] parameter is required. Format Mode Interface Config network javamode This command specifies whether or not the switch should allow access to the Java applet in the header frame of the Web interface.
A value of 0 indicates that no telnet connection can be established. The range is 0 to 5. The supported rates are,, Format Mode serviceport protocol This command specifies the servicePort configuration protocol.
If you modify this value, the change takes effect immediately. The network interface is the logical interface used for in-band connectivity with the switch via any of the switch’s front panel ports. Configure which traps the switch should generate by enabling or disabling the trap condition. If a trap condition is enabled and the condition is detected, the switch’s SNMP agent sends the trap to all enabled trap receivers. The name is the community name to be deleted. The address is the associated community SNMP packet sending address and is used along with the client IP address value to denote a range of IP addresses from which SNMP clients may use that community to access the device.
The access mode is read-only also called public. Format Mode snmp-server community rw This command restricts access to switch information. When enabled, broadcast storm traps are sent only if the broadcast storm recovery mode setting associated with the port is enabled.
Format Mode snmp-server enable traps stpmode This command enables the sending of new root traps and topology change notification traps. The maximum length of name is 16 case-sensitive alphanumeric characters. If you make multiple entries using the same IP address, the first entry is retained and processed. Format Mode snmp trap link-status all This command enables link status traps for all interfaces.
The commands are divided into two functional groups: The first interface is a logical slot and port number of a configured port-channel. Before adding a port to a port-channel, set the physical mode of the port. The interface is a logical unit, slot and port slot and port number of a configured port-channel. This command can be issued without regard for the session status enabled or disabled. Format Mode shutdown all This command disables all ports.
Default Format Mode no shutdown all This command enables all ports. If the mode is enabled, broadcast storm recovery with high and low thresholds is implemented. For Admit All mode, untagged frames or priority frames received on this interface are accepted and assigned the value of the interface VLAN ID for this port. If tagging is enabled, traffic is manial as tagged frames.
If tagging is disabled, traffic is transmitted as untagged frames. Each interface and protocol combination can only be associated with one group. Format Mode logout This command closes the current telnet connection or resets the current serial connection.
Reset means that all network connections are terminated and the boot code executes. The switch uses the stored configuration to initialize the switch. The apply command backs up the running configuration and then starts applying the commands in the script file.
The validation will stop at the first failure of a command. Otherwise when full capacity is reached, logging stops. Default Format Mode no logging wrap This command disables wrapping of in-memory logging and configures logging to stop when capacity is full. It does not clear the contents of the log. Format Mode logging host This command enables logging to a host where up to eight hosts manhal be configured.
Format Mode Global Config logging syslog This command enables syslog logging. The log messages appear here.
NETGEAR Switch GSM7248 user manual
For each configured server When a password is changed, a prompt will ask for the operator’s former password. If none, press enter. Low-address and high- address are valid IP addresses; each made up of four decimal bytes ranging from 0 to The name should be previously configured pool mahual. Default Format Mode no domain-name This command removes the domain name. Default Format Mode no option This command removes the options.
If no IP address is specified, all the conflicting addresses are displayed. The customer ID may have the value 0 to The default value of the customer ID is 0. Format Platforms that do not support priority to traffic class mapping on a per-port basis This can be considered a buffer gsm2748 for another station to assert registration for the same attribute in order to maintain uninterrupted service.
This command ggsm7248 an effect only when GVRP is enabled.
Format Mode set garp timer leaveall This command sets how frequently indicates that all registrations will be unregistered. Participants would need to rejoin in order to maintain registration.